General Options

-Tname

Tell tabs which terminal type to use. If this option is not given, tabs will use the $TERM environment variable. If that is not set, it will use the ansi+tabs entry.

-d

The debugging option shows a ruler line, followed by two data lines. The first data line shows the expected tab-stops marked with asterisks. The second data line shows the actual tab-stops, marked with asterisks.

-n

This option tells tabs to check the options and run any debugging option, but not to modify the terminal settings.

-V

reports the version of ncurses which was used in this program, and exits.

The tabs program processes a single list of tab stops. The last option to be processed which defines a list is the one that determines the list to be processed.

Implicit Lists

Use a single number as an option, e.g., -5 to set tabs at the given interval (in this case 1, 6, 11, 16, 21, etc.). Tabs are repeated up to the right margin of the screen.

Use -0 to clear all tabs.

Use -8 to set tabs to the standard interval.

Explicit Lists

An explicit list can be defined after the options (this does not use a -). The values in the list must be in increasing numeric order, and greater than zero. They are separated by a comma or a blank, for example,

tabs 1,6,11,16,21
tabs 1 6 11 16 21

Use a + to treat a number as an increment relative to the previous value, e.g.,

tabs 1,+5,+5,+5,+5

which is equivalent to the 1,6,11,16,21 example.

Predefined Tab Stops

POSIX defines several predefined lists of tab stops.

-a

Assembler, IBM S/370, first format
1,10,16,36,72

-a2

Assembler, IBM S/370, second format
1,10,16,40,72

-c

COBOL, normal format
1,8,12,16,20,55

-c2

COBOL compact format
1,6,10,14,49

-c3

COBOL compact format extended
1,6,10,14,18,22,26,30,34,38,42,46,50,54,58,62,67

-f

FORTRAN
1,7,11,15,19,23

-p

PL/I
1,5,9,13,17,21,25,29,33,37,41,45,49,53,57,61

-s

SNOBOL
1,10,55

-u

UNIVAC 1100 Assembler
1,12,20,44

Margins

A few terminals provide the capability for changing their left/right margins. The tabs program has an option to use this feature:

+m margin

The effect depends on whether the terminal has the margin capabilities:

• If the terminal provides the capability for setting the left margin, tabs uses this, and adjusts the available width for tab-stops.

• If the terminal does not provide the margin capabilities, tabs imitates the effect, putting the tab stops at the appropriate place on each line. The terminal's left-margin is not modified.

If the margin parameter is omitted, the default is 10. Use +m0 to reset the left margin, i.e., to the left edge of the terminal's display. Before setting a left-margin, tabs resets the margin to reduce problems which might arise on moving the cursor before the current left-margin.

When setting or resetting the left-margin, tabs may reset the right-margin.

/usr/share/tabset

tab stop initialization database

IEEE Std 1003.1/The Open Group Base Specifications Issue 7 (POSIX.1-2008) describes a tabs utility. However

• This standard describes a +m option, to set a terminal's left-margin. Very few of the entries in the terminal database provide the smgl (set_left_margin) or smglp (set_left_margin_parm) capability needed to support the feature.

• There is no counterpart in X/Open Curses Issue 7 for this utility, unlike tput(1).

The -d (debug) and -n (no-op) options are extensions not provided by other implementations.

A tabs utility appeared in PWB/Unix 1.0 (1977). A reduced version shipped in Seventh Edition Unix (early 1979) and in 3BSD (later the same year); it supported a -n option to set the first tab stop at the left margin. That option is not documented by POSIX.

The PWB/Unix tabs utility returned in System III (1980), and used built-in tables rather than the terminal database, to support a half-dozen hardcopy terminal (printer) types. It also had built-in logic to support setting the left margin, as well as a feature for copying the tab settings from a file.

Versions of the program in later releases of AT&T Unix, such as SVr4, added support for the terminal database, but retained the tables to support the printers. In an earlier development effort, the tab stop initialization provided by tset(1) (1982), and incorporated into tput(1) uses the terminal database,

The +m option was documented in the POSIX Base Specifications Issue 5 (Unix98, 1997), then omitted in Issue 6 (Unix03, 2004) without express motivation, though an introductory comment and optionally adjusts the margin remains, overlooked in the removal. The tabs utility documented in Issues 6 and later has no mechanism for setting margins. The +m option in ncurses tabs differs from the SVr4 feature by using terminal capabilities rather than built-in tables.

POSIX documents no limit on the number of tab stops. Other implementations impose one; the limit is 20 in PWB/Unix's tabs utility. While some terminals may not accept an arbitrary number of tab stops, ncurses tabs attempts to set tab stops up to the right margin if the list thereof is sufficiently long.

The Rationale section of the Issue 6 tabs reference page details how the committee considered redesigning the tabs and tput utilities, without settling on an improved solution. It claims that

no known historical version of tabs supports the capability of setting arbitrary tab stops.

Nevertheless, the feature described in subsection Explicit Lists above was implemented in PWB/Unix, and permits the setting of abitrary tab stops.