posix_fadvise - predeclare an access pattern for file data
Programs can use posix_fadvise() to announce an intention to access file data in a specific pattern in the future, thus allowing the kernel to perform appropriate optimizations.
advice applies to a (not necessarily existent) region starting at
offset and extending for
len bytes (or until the end of the file if
len is 0) within the file referred to by
advice is not binding; it merely constitutes an expectation on behalf of the application.
Permissible values for
Indicates that the application has no advice to give about its access pattern for the specified data. If no advice is given for an open file, this is the default assumption.
The application expects to access the specified data sequentially (with lower offsets read before higher ones).
The specified data will be accessed in random order.
The specified data will be accessed only once.
In kernels before 2.6.18, POSIX_FADV_NOREUSE had the same semantics as POSIX_FADV_WILLNEED. This was probably a bug; since kernel 2.6.18, this flag is a no-op.
The specified data will be accessed in the near future.
POSIX_FADV_WILLNEED initiates a nonblocking read of the specified region into the page cache. The amount of data read may be decreased by the kernel depending on virtual memory load. (A few megabytes will usually be fully satisfied, and more is rarely useful.)
The specified data will not be accessed in the near future.
POSIX_FADV_DONTNEED attempts to free cached pages associated with the specified region. This is useful, for example, while streaming large files. A program may periodically request the kernel to free cached data that has already been used, so that more useful cached pages are not discarded instead.
Requests to discard partial pages are ignored. It is preferable to preserve needed data than discard unneeded data. If the application requires that data be considered for discarding, then
len must be page-aligned.
may attempt to write back dirty pages in the specified region, but this is not guaranteed. Any unwritten dirty pages will not be freed. If the application wishes to ensure that dirty pages will be released, it should call fsync(2) or fdatasync(2) first.
On success, zero is returned. On error, an error number is returned.
fd argument was not a valid file descriptor.
An invalid value was specified for
The specified file descriptor refers to a pipe or FIFO. (ESPIPE is the error specified by POSIX, but before kernel version 2.6.16, Linux returned EINVAL in this case.)
Since Linux 3.18, support for the underlying system call is optional, depending on the setting of the CONFIG_ADVISE_SYSCALLS configuration option.
POSIX.1-2001, POSIX.1-2008. Note that the type of the
len argument was changed from
off_t in POSIX.1-2003 TC1.
Under Linux, POSIX_FADV_NORMAL sets the readahead window to the default size for the backing device; POSIX_FADV_SEQUENTIAL doubles this size, and POSIX_FADV_RANDOM disables file readahead entirely. These changes affect the entire file, not just the specified region (but other open file handles to the same file are unaffected).
The contents of the kernel buffer cache can be cleared via the
/proc/sys/vm/drop_caches interface described in proc(5).
Some architectures require 64-bit arguments to be aligned in a suitable pair of registers (see syscall(2) for further detail). On such architectures, the call signature of posix_fadvise() shown in the SYNOPSIS would force a register to be wasted as padding between the
offset arguments. Therefore, these architectures define a version of the system call that orders the arguments suitably, but is otherwise exactly the same as posix_fadvise().
For example, since Linux 2.6.14, ARM has the following system call:
long arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len);
These architecture-specific details are generally hidden from applications by the glibc posix_fadvise() wrapper function, which invokes the appropriate architecture-specific system call.
In kernels before 2.6.6, if
len was specified as 0, then this was interpreted literally as "zero bytes", rather than as meaning "all bytes through to the end of the file".
This page is part of release 4.15 of the Linux
man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.